基于结合部的HSK主轴-刀柄系统动态特性分析
陈建1;王贵成1,3;田良2;沈春根1;郑登升1
1.江苏大学,镇江,212013
2.成都工具研究所有限公司,成都,610051
3.南通理工学院,南通,226002
Dynamic Property Analysis of HSK Spindle-toolholder System Based on Joint Part
Chen Jian1;Wang Guicheng1,3;Tian Liang 2;Shen Chungen1;Zheng Dengsheng1
1.Jiangsu University,Zhenjiang,Jiangsu,212013
2.Chengdu Tool Research Institute Co., Ltd.,Chengdu,610051
3.Nantong Institute of Technology,Nantong,Jiangsu,226002
摘要 建立了HSK主轴-刀柄结合部的有限元模型(FEM),利用弹性理论和黏性阻尼理论辨识结合部内各位置的刚度和阻尼参数。提出将HSK主轴-刀柄系统分为HSK主轴、主轴-刀柄结合部和刀柄三部分:HSK主轴与刀柄简化为多段Timoshenko梁,并使用响应耦合法来计算其频响函数;主轴-刀柄结合部简化为多点弹簧-阻尼模型,采用多点响应耦合法来计算其频响函数;将各个部件的频响函数进行刚性耦合,进而获得基于结合部的HSK主轴-刀柄系统频响函数。分别假定HSK主轴-刀柄结合部为刚性连接、5点弹性连接和7点弹性连接,计算其频响函数,并与实验结果相比较得到相应的结论。
关键词 :
HSK主轴-刀柄系统 ,
频响函数 ,
结合部 ,
动态特性
Abstract :The HSK spindle-toolholder FEM was modeled and the stiffness and damp parameters of joint
part were identified with elastic theory and damp theory.The HSK spindle-toolholder system
could be divided into three parts,such as HSK spindle,spindle-toolholder joint part and toolholder. HSK spindle and toolholder could be simplified as Timoshenko beam, and the FRF could be gained with receptance coupling theory.The spindle-toolholder joint part might be simplified as spring-damp model,and the FRF could be achieved with multi-points receptance coupling theory. Then the FRF of system was gained with rigid coupling theory.The spindle-toolholder was treated as rigid connection,five-points connection and seven-points connection,and the tip-point FRFs of system were computed.At last, comparing these FRFs with experimental FRF, some results may be obtained.
Key words :
joint part
dynamic performance
基金资助: 国家科技重大专项(2013ZX04009031)
National Science and Technology Major Project(No. 2013ZX04009031)
引用本文:
陈建1;王贵成1,3;田良2;沈春根1;郑登升1. 基于结合部的HSK主轴-刀柄系统动态特性分析[J]. 88必发娱乐手机版, 2016, 27(03): 296-301.
Chen Jian1;Wang Guicheng1,3;Tian Liang 2;Shen Chungen1;Zheng Dengsheng1. Dynamic Property Analysis of HSK Spindle-toolholder System Based on Joint Part. China Mechanical Engineering, 2016, 27(03): 296-301.
链接本文:
/CN/ 或
[1]
Erturk A,Ozguven H N,Budak E.Analytical Modeling of Spindle-tool Dynamics on
Machine Tools Using Timoshenko Beam Model and Receptance Coupling for the Prediction
of Tool Point FRF[J].International Journal of Machine Tools &
Manufacture,2006,46:1901-1912.
[2]
Ozsahin O,Erturk A,Ozguven H N,et al. A Closed-form Approach for Identification
of Dynamical Contact Parameters in Spindle-holder-tool Assemblies,International
Journal of Machine Tools & Manufacture,2009,49:25-35.
[3]
Namazi M,Altintas Y.Modeling and Identification of Tool Holder-spindle Interface
Dynamics[J].International Journal of Machine Tools & Manufacture,2007,47:1333-
1341.
[4]
程强,刘新宇,赵永胜.基于频响函数的主轴-刀柄结合部参数辨识方法[J].北京工业大学学
报,2013,39(8):1144-1147.
Cheng Qiang,Liu Xinyu,Zhao Yongsheng.Identification of Dynamical Contact Parameters for
Spindle-tool Holder Interface Based on Frequency Response Functions[J].Journal of
Beijing Technology University,2013,39(8):1144-1147.
[5]
Budak E,Ertürk A.A Modeling Approach for Analysis and Improvement of
Spindle-holder-tool Assembly Dynamics[J].Annals of the CIRP,2006,56:1235-1239.
[6]
Erturk A,Ozguven H N,Budak E.Effect Analysis of Bearing and Interface Dynamics
on Tool Point FRF for Chatter Stability in Machine Tools by Using a New Analytical
Model for Spindle-tool Assemblies[J].International Journal of Machine Tools &
Manufacture,2007,47:23-32.
[7]
楼梦麟,任志刚.Timoshenko简支梁的振动模态特性精确解[J].同济大学学报,2002,30(8):911-915.
Lou Menglin,Ren Zhigang.Precise Solution to Modal Characteristics of Timoshenko Pin-
ended Beams[J].Journal of Tongji University,2002,30(8):911-915.
[8]
Park S,Altintas Y,Movahhedy M.Receptance Coupling for End Mills[J].International
Journal of Machine Tools & Manufacture,2003,43:889-896.
[9]
Schmitz T L,Powell K,Won D.Shrink Fit Tool Holder Connection Stiffness/Damping
Modeling for Frequency Response Prediction in Milling[J].International Journal of
Machine Tools & Manufacture,2007,47:1368-1380.
[10]
Filiz S,Cheng C H,Powell K B,et al.An Improved Tool-holder Model for RCSA
Tool-point Frequency Response Prediction[J].Precision Engineering,2009,33:26-36.
[11]
Schmitz T L,Duncan G S.Receptance Coupling for Dynamics Prediction of
Assemblies with Coincident Neutral Axes[J].Journal of Sound and
Vibration,2006,289:1045-1065.
[12]
Hanna I M,Agapiou J S.Modeling the HSK Toolholder-spindle Interface
[J]
Transactions of the ASME,2002,124:734-744.
[13]
Agapiou J S.A Methodology to Measure Joint Stiffness Parameters for
Toolholder-spindle Interface[J].Journal of Manufacture System,2005,24:13-20.
[14]
陈建,王贵成.HSK 热装刀柄的加热性能分析[J].88必发娱乐手机版,2013,24(12):3235-3239.
Chen Jian,Wang Guicheng.Heat Performance Analysis of HSK Shrink Toolholder,China
Mechanical Engineering,2013,24(12):3235-3239.
[15]
王贵成,王树林,董广强.高速加工工具系统[M].北京:国防工业出版社,2005.
[1]
陈剑;邓支强;乔晋红. 飞机舵面液压助力器及舵面系统建模与性能仿真 [J]. 88必发娱乐手机版, 2017, 28(07): 800-805.
[2]
左希庆1,2;阮健1;李胜1;刘国文2;孙坚1. [J]. 88必发娱乐手机版, 2017, 28(04): 451-455.
[3]
黄俊;袁军堂;汪振华. [J]. 88必发娱乐手机版, 2016, 27(24): 3294-3300.
[4]
宋智勇1,2;李晴朝1;姜忠1;康文俊1;杜丽1;王伟1. [J]. 88必发娱乐手机版, 2016, 27(23): 3157-3161,3166.
[5]
朱坚民; 何丹丹; 田丰庆; 赵全龙. [J]. 88必发娱乐手机版, 2016, 27(20): 2765-2773.
[6]
吴金波;宋宇宸. [J]. 88必发娱乐手机版, 2016, 27(15): 1989-1996.
[7]
马伟1;景月帅1;李济顺1,2;邹声勇2;薛玉君1;杨芳1. [J]. 88必发娱乐手机版, 2016, 27(14): 1870-1876.
[8]
周鑫1,2;许允斗1,2;姚建涛1,2;郑魁敬1,2;赵永生1,2. [J]. 88必发娱乐手机版, 2016, 27(09): 1137-1142,1149.
[9]
汪中厚;袁可可;李刚. [J]. 88必发娱乐手机版, 2016, 27(05): 622-626.
[10]
倪敬;李璐;许静;吴参. [J]. 88必发娱乐手机版, 2016, 27(03): 302-307,314.
[11]
吴加权;叶飞;李红艳;张馨予;马琨. [J]. 88必发娱乐手机版, 2016, 27(02): 156-160.
[12]
陈勇将1;汤文成2;干为民1;孟浩东1. [J]. 88必发娱乐手机版, 2016, 27(02): 178-186.
[13]
陈建1;田良2;商宏谟2;沈春根1;王贵成1,3. [J]. J4, 2015, 26(9): 1161-1166.
[14]
刘雪梅;李爱平;谭顺利. HSK刀柄-主轴结合面接触特性及其影响分析 [J]. J4, 2015, 26(8): 1000-1005.
[15]
惠烨1,2;黄玉美1;李艳1. 切向载荷下螺栓结合部静特性分析及试验 [J]. J4, 2015, 26(7): 892-898.